PREWIRED KIT LES PAUL


Les Paul Modern Prewired Kit with Bumblebee Caps

The wiring of this wiring harness is identical to that of the current Les Pauls. Replacing the original wiring is also worthwhile with this kit, read below. This kit is equally suitable for humbuckers as well as P 90 Pickups.

 

When using P-90 pickups we can also equip the kit with a treble bleed on request. The treble leed allows the volume depot to be used over the entire bandwidth without losing the highs when turning down.  With humbuckers, a treble bleed doesn't really make sense.

 

Details:

  •   CTS 500K 3/4" (19.05mm) Long Shaft or 3/8" (9.52mm) Short Shaft Potentiometer, 3/8" thread
  •   ARTY's Bumblebee .022 uF Vintage Replica Capacitors
  •   SWITCHCRAFT 1/4" Mono Audio Jack
  •   Reinforced Ground Connection between the Potentiometers, also for easier installation
  •   easy to understand Wiring Diagram

 

What's the difference between Gibson 50's vs. Modern Wiring?

50's Wiring

  •     when turning down the Volume more heights are remaining
  •     a turn of the Tone also affects the Volume
  •     with the Volume fully turned up there's a little more clarity and output

Modern Wiring

  •    better Volume control
  •    turning the Tone does not change the Volume
  •    significant loss of height when turning down the Volume (can be reduced with a Treble Bleed)

 

If you want to completely replace the wiring of your Les Paul, we also have the matching prewired 3-Way Toggle Switch from Switchcraft on offer.

 

WHICH POTS AND WHICH SWITCH IS THE RIGHT ONE?


There are countless Les Paul models, and there are always more. In the different models different toggle switches and pots are used. All LP models with curved top until 1977 have short pots and a long toggle switch. For the most common models since 1977 we have compiled a small overview below. To mount the long switch in the Les Paul you also need a "Deep Round Nut". The Deep Round Nut extends the otherwise too short thread of the switch, and must be ordered separately.

Models since 1977     Switch     Pots      
Standard                     long        long
Studio                         short       long
Traditional                    long        long
Custom                       long        long
Special                        short       short

 

The shipping costs for most EU countries are € 12,-. You can find more information about shipping costs under the link directly below the product costs (inkl. Mwst., zzgl. Versandkosten). If your destination country is not listed here, please contact us to calculate the shipping costs.

 

If you need help with the checkout form or payment, please don't hestitate to contact us via e-mail. We just need your address and the designation of the desired items. As soon as we have received the above information, we will send you the detailed invoice.

 

96,00 €

  • auf Lager
  • Versand binnen 3-5 Werktage

Why a Prewired GUITAR WIRING HArness from Arty's Custom Guitars?

 

BECAUSE WE ARE ONLY SATISFIED WITH THE BEST.


All our prewired kits have matched pots and caps. This means that we measure all potentiometers and capacitors before installation, select them, and use them according to their values where they deliver the best possible result in combination with the pickups. This is important because original pots have tolerances of up to +-20%. In extreme cases, a 500k pot can have values of only 400k or up to 600k ohms. Not infrequently good pickups are replaced unnecessarily, because they sound muddy, weak or thin. In reality, however, the problem is often not due to bad pickups, but simply to inferior wiring, which mercilessly destroys the actually perfect sound.

We compared enormous quantities of capacitors in interaction with various pickups and thus determined the most suitable tone caps under real conditions. The capacitors are hand-selected HQ film capacitors with very low tolerance, very similar in design to the originals from the fifties. The vintage paper wax skin gives the caps an additional look. Our capacitors are so close to the originals of the 50's that nobody will hear a difference.

In all our kits only the best components from well-known manufacturers like CTS, Switchcraft, CRL or Oak Grigsby are used. All kits are carefully manufactured in small quantities and professionally handcrafted, and delivered to satisfied customers all over the world.

Wünsche, Fragen, Anregungen, ...

WIR FREUEN UNS AUF DEINE ANFRAGE!

 

Wishes, questions, suggestions,  ...

WE LOOK FORWARD TO YOUR REQUEST!